sourcingmap Washing Machine Drain Hose Clip Clamp 1.2 Inch Dia 2 Inch Width 2 Pcs

Product Information

Inside the property, use an SDS drill and a long drill bit to drill through the wall in the position that you will install the waste and where it will exit the property. Ensure it is high enough so that once the pipe runs through you get the required minimum of 1:40 drop to ensure correct drainage. This is one of those jobs you’ve probably never given much thought to until it comes time to install a washing machine in a new house and everything isn’t quite set up the same as it was in the old place. Maybe the waste pipes under the sink are all different, or perhaps you can’t even see anywhere to attach the hose to. Well worry not, we have all bases covered here, so continue on and read our guide. Connecting Washing Machine Waste Pipe However this isn’t always possible due to the position of existing appliances or kitchen units so it may end up having to be installed some way away from any easily accessible drainage points. So, in answer to the question of; do you have to install a waste trap? The answer is a definite yes! Tools and Materials Needed for Installing a Waste Trap Due to the nature of the areas in which sinks tend to exist, waste traps can over time fill up with all sorts of unmentionable substances.

The standpipe waste trap is the best solution in terms of waste traps for both washing machines and dishwashers. The main reason for this is that it has its own purpose made outlet that takes waste water from the machine into the remaining foul pipework or its own specific foul waste if needed. When installing the standpipe it should be clipped to the wall at least twice in its vertical length and at every 400mm along its horizontal length. Any sagging of the pipework can lead to puddles of stagnant water in the pipe which can cause horrible smells. If you have a rotatable spigot then you can move this into an upward position to help with that. You may well have a fixed spigot as I do. If this is indeed what you have under your sink then you will need to move the pipe into a position where it feeds down into the spigot at some point. Here you can see the full waste trap Dishwasher and washing machine With the old waste out the way, unscrew the compressions nuts and remove the washer and seals for the new one and slip them over the ends of the pipes.

Positioning Appliances and Waste Outlets

Installing a self sealing vent, because it reduces negative pressure in the waste system, can be used to remove the noises associated with gurgling pipes and basins. It also removes the need for air admittance valves. Positioning Appliances and Waste Outlets To do this, loosen the Jubilee Clip, if there is one and then push the waste pipe over the tapered nozzle all the way down as far as it will go. This, as its name suggests, straps onto the soil pipe and the waste pipe from the washing machine or dishwasher and pushes inside the rubber collar. A hole is made in the soil pipe to allow free passage of waste.

If your sink has a strainer then it may be connected in a similar way to the image below, in which case you can simply replace the 90° joint with a T-joint and screw on 40mm appliance compression nozzle. Washing machines and dishwashers, once installed, must deliver their waste water to the foul drainage system for your home. This is the same system which takes the toilet and basin waste. It is illegal to put this waste water into your surface water system which is the water collected by your gutters. Once in place, tighten the Jubilee Clip all the way to hold the pipe in place. Once this is done, you’re all finished.Pop the appliance in position and then position the waste into the standpipe. This will either involve dropping the hose down the standpipe, ensuring that there is at least 100mm between its end and the water in the trap or hooking the hook of the pipe over the top. If you do this, make sure that you run your machine empty the next time you use to clear out any unwanted chemicals in there. Next cut a length of pipe to run through the wall from the 90° bend and ensure there is around 75mm clear from the face of the wall to allow for the compression joint on the trap. When cut, glue this into the 90° joint.

In some cases like this it may be possible to extend the waste pipe hose on the appliance to reach a little further but this should only be done if the manufacturer allows it and you use the correct extension kit stated by the manufacturers and that it doesn’t exceed a total length once extended of more than 1.5 metres. There are 3 types of waste trap that are generally used for appliances, with 2 being used much more regularly than the third. The main types are the standpipe waste trap and the sink and appliance waste. The third fairly uncommonly used type is the self sealing waste trap. Sink and Appliance Waste Trap

Further Help

You want to push your grey waste pipe onto one of these spigots, but make sure you have a jubilee clip on the hose first, this should be nice and loose and just floating for the time being. If yours look like the image above with the “ribs” on them then this means they can be cut down to accommodate different hose widths. You probably don’t need to bother with this however and should just leave it as is. In some instances, running a new waste pipe from an existing waste isn’t going to be possible or there may be a convenient drain or soil pipe just the other side of the wall that would be much easier to run a waste to rather than removing kitchen units or trying to alter them. Using a piece of finer 240 grit sandpaper, sand off the cut end to smooth it off and remove any burrs. To find out more about how waste traps work, see our project here. Types of Waste Trap for Washing Machines and Dishwashers One final important point is that the length of waste pipe for both washing machines and dishwashers should not exceed 3 metres in length. This includes the waste hose running from the machine. Do You Have to Install a Waste Trap?

In terms of the waste trap itself the document states that it should be at minimum 40mm in diameter and the depth water in the trap to form an effective seal should be at least 75mm. Next, using a tape measure, measure from the new pipe joint over to where the new standpipe will be positioned and cut a piece of UPVC pipe to length, remembering to measure from inside the collar of the joint where the pipe will butt up to. Tidy up the end with a piece of sandpaper.I have illustrated an image below for you to make it easier to see what they are. Spigots on a waste trap Which ever machine waste trap you are going to install you will need a number of tools and products to get the job done correctly. The next job is to remove the old waste trap. This is a fairly easy task and just involves unscrewing the 2 compression nuts holding it in place.